開關電源、氣源、液壓源的問題往往會導致山東自動焊接設備出現異常，比如電源系統的問題，涉及到生產車間所有的電源系統故障，比如電源低、燒壞、電源線插頭松動、接觸不良等。

The problems with switching power, air, and hydraulic sources often lead to abnormalities in Shandong automatic welding equipment, such as power system problems, which involve all power system failures in the production workshop, such as low power supply, safety burning, loose power cord plugs, and poor contact.

氣泵或液壓泵未打開時，氣動三聯或雙接頭未打開，液壓傳動系統中的卸荷閥或某些壓力閥未打開等。，測試儀器時要涉及到以下幾個方面:開關電源，涉及到各機器設備供電系統的開關電源和生產車間的電源。

When the air pump or hydraulic pump is not turned on, the pneumatic triple or double joint is not turned on, and the unloading valve or some pressure valves in the hydraulic transmission system are not turned on., When testing instruments, the following aspects need to be involved: switching power supply, which involves the switching power supply of various machine equipment power supply systems and the power supply of production workshops.

自動焊接機壓力調節閥、繼電器、流量調節閥的常規檢查

Routine inspection of pressure regulating valves, relays, and flow regulating valves for automatic welding machines

繼電器和磁感應感應器一樣，長期使用會導致接地的粘結，無法保證用電設備的正常控制電路。焊接機和設備需要更換。在氣動或液壓傳動系統中，節流閥的開度和壓力閥的壓力調節變黃，機器和設備的振動會導致松動或滑動。這些裝置和傳感器一樣，都是自動化機械中日常工作中需要維護的部件。

Relays, like magnetic induction inductors, can lead to ground bonding after long-term use, which cannot guarantee the normal control circuit of electrical equipment. The welding machine and equipment need to be replaced. In pneumatic or hydraulic transmission systems, the opening of the throttle valve and the pressure regulation of the pressure valve turn yellow, and the vibration of machines and equipment can cause loosening or sliding. These devices, like sensors, are components that require maintenance in daily work of automated machinery.

例行檢查自動焊接機的傳感器位置是否偏移

Routine check if the sensor position of the automatic welding machine is offset

由于設備維護和管理人員的疏忽，很可能會遺漏一些傳感器的位置，如不到位、傳感器故障、靈敏度故障等。，所以需要例行檢查傳感器的傳感技術位置和靈敏度，如有偏差立即調整。如果傳感器損壞，請立即更換。很多時候，除此之外，因為自動化機械的震動，大部分傳感器在長期使用后都會松動。因此，在日常工作和維護中，需要定期檢查傳感器的位置是否合理，固定是否牢固。

Due to the negligence of equipment maintenance and management personnel, it is possible to miss the location of some sensors, such as inadequate positioning, sensor failure, sensitivity failure, etc., So it is necessary to regularly check the sensor's sensing technology position and sensitivity, and adjust immediately if there is any deviation. If the sensor is damaged, please replace it immediately. Many times, in addition to this, due to the vibration of automated machinery, most sensors become loose after long-term use. Therefore, in daily work and maintenance, it is necessary to regularly check whether the position of the sensor is reasonable and whether it is firmly fixed.

例行檢查自動焊接機的電磁閥是否有換向操作

Routine inspection of the electromagnetic valve of the automatic welding machine for reverse operation

電磁閥通過電磁鐵吸引閥芯，使氣缸做好換向工作。當電磁鐵不工作時，閥芯不工作，導致氣缸不能工作。如果氣控回路中濕氣和煙霧太多，閥芯就會被卡住、堵塞，然后氣缸就不能工作了。

The solenoid valve attracts the valve core through an electromagnet, enabling the cylinder to perform reversing work. When the electromagnet is not working, the valve core does not work, resulting in the cylinder not working. If there is too much moisture and smoke in the air control circuit, the valve core will be stuck, blocked, and the cylinder will not work.

自動焊接機所有控制電路的常規檢查

Routine inspection of all control circuits of automatic welding machines

檢查電路中的電線是否短路，特別是線槽中的電線是否因拉扯而被線槽切斷，檢查氣管是否有損壞的折痕，檢查液壓油管是否堵塞。如果氣管嚴重折皺，應立即更換，液壓油管也應更換。

Check if the wires in the circuit are short circuited, especially if the wires in the trunking are cut by the trunking due to pulling, check if there are any damaged creases in the air pipe, and check if the hydraulic oil pipe is blocked. If the trachea is severely wrinkled, it should be replaced immediately, and the hydraulic oil pipe should also be replaced.

在自動焊接機確保申訴方法步驟正確后，故障很可能出現在自動機的控制面板，但不可能是程序問題。，控制面板損壞是毫無疑問的。只要沒有嚴重的短路故障，控制面板內部是有短路保護的，通常的短路故障是不會燒壞控制面板的。更多相關事項就來我們網站http://gouteli.cn咨詢！

After the automatic welding machine ensures that the appeal method steps are correct, the fault is likely to occur in the control panel of the automatic machine, but it cannot be a program issue. Firstly, there is no doubt that the control panel is damaged. As long as there is no serious short circuit fault, the control panel has short circuit protection inside, and normal short circuit faults will not burn the control panel. For more related matters, come to our website http://gouteli.cn consulting service